As(tss nss) 15 25 60 35mm One Way Bearings Roller Freewheel Clutch Bearing

Type AS Is A Roller Type Freewheel Non-Bearing Supported. Bearings Are Required To Support Axial And Radial Loads. Lubrication And Sealing Must Also Be Provided By The Installation. Nominal Outside Dimensions Are The Same As Series 62...Ball Bearings.

LIÊN HỆ NGAY tải xuống pdf

Chi tiết

Thẻ

Highlight: nss 60 bearing, nss25 bearing, tss bearings

Tên:	AS One Way Sprag Bearing Overrunning Clutch	Vật liệu:	Thép chịu lực GCR 15
Kiểu:	Vòng bi một chiều	Thichness (mm):	19-140
Mô-men xoắn (Nm):	2.1-1063	Trọng lượng (Kg):	0.01-1.41
Kích thước lỗ khoan (mm):	6-80	Warranty:	12 Months

AS NSS TSS One Way Roller Type Freewheel Clutch

Giới thiệu sản xuất

A Typical Arrangement Is To Install This Type Alongside A Series 62 Bearing Within The Same Location Tolerances, As Shown On The Following Page. The Inner Race Is Keyed To The Shaft (Except 6 Mm Bore).
The Outer Race Has A Positive R6 Tolerance To Give A Press Fit In A H7 Housing. The Outer Housing Must Be Strong Enough
To Not Expand After Assembly. This Design Can Accept An Axial Misalignment Of Inner And Outer Race Of ± S/2.

The dimensions of the AS type wedge type one-way clutch are the same as those of the 62 series deep groove ball bearings (CSK40). It is a combination of a deep groove ball bearing and a sprag clutch, which has been filled with grease. The seal can prevent dust above 0.3mm from entering the interior. The transmission of torque is in the form of interference fit. The outer ring is pressed with a rigid enough frame with N6 tolerance, and the inner ring is pressed with the outer diameter of the working shaft. When installing, pay attention not to knock the inner ring to press the outer ring into the frame, and not to knock the outer ring to press the inner ring to squeeze into the outer diameter of the shaft. The transmission torque is small (7.4~260N.m), and the limit speed is high. Widely used in printing machinery, packaging machinery, food machinery, electric drum, reducer and testing equipment, etc.

Thông số sản phẩm

Kiểu	Kích cỡ	Torque	Overrunning speeds		Dimensions						Cân nặng	Kéo mô-men xoắn
AS (NSS)	dH7	TKN1)	nimax2)	namax3)	Dr6	D5	L	s	e	f	Cân nặng	Kéo mô-men xoắn
	[mm]	[Nm]	[phút-1]	[phút-1]	[mm]	[mm]	[mm]	[mm]	[mm]	[mm]	[Kilôgam]	[Ncm]
	6	2.1	5000	7500	19	15.8	6	0.3	0.6	0.3	0.01	0.18
	8	3.8	4300	6500	24	20	8	1.3	0.6	0.6	0.02	0.24
	10	6.8	3500	5200	30	25.9	9	1.3	0.6	0.6	0.03	0.36
	12	13	3200	4800	32	28	10	1.3	0.6	0.6	0.04	0.48
	15	14	2800	4300	35	31	11	1.4	0.6	0.6	0.05	0.7
	20	40	2200	3300	487	40	14	2.4	0.8	0.8	0.12	1.4
	25	56	1900	2900	52	45.9	15	2.4	0.8	0.8	0.14	2.4
	30	90	1600	2400	62	55	16	2.4	0.8	1	0.22	7.8
	35	143	1300	2000	72	64	17	2.5	0.8	1	0.31	9
	40	185	1200	1800	80	72	18	2.5	0.8	1	0.39	10
	45	218	1000	1600	85	77	19	2.5	1.2	1	0.44	11
	50	230	950	1500	90	82	20	2.5	1.2	1	0.49	13
	55	308	800	1300	100	90	21	2.5	1.2	1	0.66	14
	60	508	700	1100	110	100	22	2.5	1.2	1.5	0.81	26
	80	1063	600	900	140	128	26	2.5	1.2	1.5	1.41	58

NOTES:

AS6 Without Keyway. ØD = -0-0,009
AS8-12 Keyway To DIN 6885.1.
Các kích thước khác theo DIN 6885.3
1) T Max = 2 × T KN
2) Vượt cuộc đua bên trong
3) Vượt vòng đua bên ngoài
Mounting Dimensions Are Identical To Ball Bearings Series 62

As(tss nss) 15 25 60 35mm One Way Bearings Roller Freewheel Clutch Bearing